Imc-networks IE-IMCV-T1-MUX/4 Bedienungsanleitung

IE-iMcV-T1-Mux/4 + Ethernet Operation Manual

6 iView² Management Software iView² is the IMC Networks management software designed specifically for the IMC Networks “iMcV” family of modules. It f

7 LED Operation The IE-iMcV-T1-Mux/4 + Ethernet features diagnostic LEDs as explained below. 10/100BaseT Connector LNK: • OFF when port is not li

8 SFP Ports or One model offers two SFP (A and B) ports for 1+1 protection; a second model offers one SFP without protection. ACT: • Glows gre

9 DIP Switch Assignments DIP Switch Assignments A single 10-position DIP Switch is located on the unit to set the configuration. The switch positions

10 Installation Instructions Each IE-iMcV-T1-Mux/4 + Ethernet module requires two slots in an iMedia Chassis Series, MediaChassis/2 Series, or IE-Medi

11 Configuration Options The following sections describe the configurable features. From the CLI "Unit Configuration," use the "Facto

12 Fiber Fault Loopback (FFL) When a Fiber LOS is detected, the unit sends a Remote Alarm Indication) back to the fiber in the opposite direction. Th

13 Loopback Each T1 port can be tested in loopback mode by enabling either a Host loopback or Remote loopback test path. This capability allows the e

14 Console Screens Configuration Using the Console Port The following section describes configuration using the console screens. The Remote module is

15 Main Menu From the main menu, the end-user can view essential unit configuration data and a clock indicating when the displayed information was las

FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A computing device, pursuan

16 The screen displays the current status for items 1 through 8. For security reasons, the current username and password are not displayed. For item

17 SFP Line Status Screen The SFP Line Status screen displays the status of the Host and Remote SFP links. The detailed SFP information may be view

18 Enter the number of the menu item to change its configuration, and then enter the new value(s) when prompted. Ethernet Port Status Screen This scre

19 Host T1 Port Setup Screen Enter the number of the menu item to edit, and enter the new value(s) when prompted. T1 Port Status Screen Use this sc

20 Fiber Optic Port Verification As a troubleshooting aid, the fiber optic ports can be verified by placing a physical loopback optical line on the po

21 T1 Port Verification By placing a physical loopback connection on the T1 port, a valid signal can be detected by each individual T1 port to verify

22 T1 Port Mating Connector Pinout The following table lists the pin configuration for the standard RJ-48 T1 port mating connectors. Pin Signal 1

23 RS-232 Serial Console Port The following table lists the pin configuration for the RS-232 3-pin Mini Jack mating connector for the console serial p

24 Troubleshooting • All IE-iMcV-T1-Mux/4 + Ethernet units are shipped configured as Host units via DIP Switch #1 = OFF. The Remote unit should be set

25 Specifications Power Consumption (Typical): 0.96A @ +5 VDC Operating Temperature: +32°F to +158°F (0°C to +70°C) Storage Temperature: -40°F to +158

ii Table of Contents FCC Radio Frequency Interference Statement -------------------------------------------------- i Warranty ------------------------

26 Definition of Terms/Acronyms The following are terms and phrases used within this manual, or which are found in documents associated with this equi

27 FFL Fiber Fault Loopback: When the fiber line fails, the Ethernet port that is being forwarded over the fiber line is forced out of LINK. Simila

28 RAI Remote Alarm Indication: Status information received from the line indicating there is an alarm condition at the far end of the transport. SF

29 IMC Networks Technical Support Tel: (949) 465-3000 or (800) 624-1070 (in the U.S. and Canada); +32-16-550880 (Europe) Fax: (949) 465-3020 E-M

30 Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, whi

31 Certifications CE: The products described herein comply with the Council Directive on Electromagnetic Compatibility (2004/108/EC). European

19772 Pauling • Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 • FAX: (949) 465-3020 www.imcnetworks.com © 2010 IMC Networks. All ri

iii Troubleshooting -------------------------------------------------------------------------------------24 Specifications----------------------------

1 About the IE-iMcV-T1-Mux/4 + Ethernet Overview The IE-iMcV-T1-Mux/4 + Ethernet is a media converter that transports four independent T1 lines over a

2 The IE-iMcV-T1-Mux/4 + Ethernet offers the following features: • Four T1 ports with RJ-48 connectors • One full bandwidth Ethernet 10/100BaseT port

3 Product Application The IE-iMcV-T1-Mux/4 + Ethernet delivers 4 T1 lines to a customer's site over a protected, dedicated fiber line. In additi

4 configuration on the unit will be used. The stored configuration can be retrieved from the SNMP Management Module or the DIP Switches. • Replacing t

5 1+1 Protection on the Fiber Interface mode The fiber transport is a 1+1 protection switched transport. It provides very fast (<50 mSec) switch-to